Mineralogical and chemical characterization of mining waste and utilization for carbon sequestration through mineral carbonation.

Mining activities have often been associated with the issues of waste generation, while mining is considered a carbon-intensive industry that contributes to the increasing carbon dioxide emission to the atmosphere. This study attempts to evaluate the potential of reusing mining waste as feedstock material for carbon dioxide sequestration through mineral carbonation. Characterization of mining waste was performed for limestone, gold and iron mine waste, which includes physical, mineralogical, chemical and morphological analyses that determine its potential for carbon sequestration. The samples were characterized as having alkaline pH (7.1-8.3) and contain fine particles, which are important to facilitate precipitation of divalent cations. High amount of cations (CaO, MgO and Fe2O3) was found in limestone and iron mine waste, i.e., total of 79.55% and 71.31%, respectively, that are essential for carbonation process. Potential Ca/Mg/Fe silicates, oxides and carbonates have been identified, which was confirmed by the microstructure analysis. The limestone waste composed majorly of CaO (75.83%), which was mainly originated from calcite and akermanite minerals. The iron mine waste consisted of Fe2O3 (56.60%), mainly from magnetite and hematite, and CaO (10.74%) which was derived from anorthite, wollastonite and diopside. The gold mine waste was attributed to a lower cation content (total of 7.71%), associated mainly with mineral illite and chlorite-serpentine. The average capacity for carbon sequestration was between 7.73 and79.55%, which corresponds to 383.41 g, 94.85 g and 4.72 g CO2 that were potentially sequestered per kg of limestone, iron and gold mine waste, respectively. Therefore, it has been learned that the mine waste might be utilized as feedstock for mineral carbonation due to the availability of reactive silicate/oxide/carbonate minerals. Utilization of mine waste would be beneficial in light of waste restoration in most mining sites while tackling the issues of CO2 emission in mitigating the global climate change.

Carbon dioxide sequestration of iron ore mining waste under low-reaction condition of a direct mineral carbonation process.

Mining waste that is rich in iron-, calcium- and magnesium-bearing minerals can be a potential feedstock for sequestering CO2 by mineral carbonation. This study highlights the utilization of iron ore mining waste in sequestering CO2 under low-reaction condition of a mineral carbonation process. Alkaline iron mining waste was used as feedstock for aqueous mineral carbonation and was subjected to mineralogical, chemical, and thermal analyses. A carbonation experiment was performed at ambient CO2 pressure, temperature of 80 °C at 1-h exposure time under the influence of pH (8-12) and particle size (< 38-75 µm). The mine waste contains Fe-oxides of magnetite and hematite, Ca-silicates of anorthite and wollastonite and Ca-Mg-silicates of diopside, which corresponds to 72.62% (Fe2O3), 5.82% (CaO), and 2.74% (MgO). Fe and Ca carbonation efficiencies were increased when particle size was reduced to < 38 µm and pH increased to 12. Multi-stage mineral transformation was observed from thermogravimetric analysis between temperature of 30 and 1000 °C. Derivative mass losses of carbonated products were assigned to four stages between 30-150 °C (dehydration), 150-350 °C (iron dehydroxylation), 350-700 °C (Fe carbonate decomposition), and 700-1000 °C (Ca carbonate decomposition). Peaks of mass losses were attributed to ferric iron reduction to magnetite between 662 and 670 °C, siderite decarbonization between 485 and 513 °C, aragonite decarbonization between 753 and 767 °C, and calcite decarbonization between 798 and 943 °C. A 48% higher carbonation rate was observed in carbonated products compared to raw sample. Production of carbonates was evidenced from XRD analysis showing the presence of siderite, aragonite, calcite, and traces of Fe carbonates, and about 33.13-49.81 g CO2/kg of waste has been sequestered from the process. Therefore, it has been shown that iron mining waste can be a feasible feedstock for mineral carbonation in view of waste restoration and CO2 emission reduction.

Toxicity effect of Diuron on gill tissue structure and the tissue residue of blood cockles (Tegillarca granosa).

This study aimed to identify the toxicity effect of Diuron on Tegillarca granosa by determining accumulation in the soft tissues and alteration on the gill tissue structure. Wild stocks T. granosa were grouped to identify the initial Diuron concentration and 48-h exposure in different concentrations (0, 1, 2, 3, and 4 mg·L-1). The Diuron in tissue was extracted using an established procedure and identified using High-Performance Liquid Chromatography (HPLC). Gills were analysed for histopathological study; tissue structure was classified and scored using a developed scoring system. Diuron concentration in the soft tissue of exposed T. granosa was in the range 1.27-8.09 mg·kg-1, w/w and not proportionately increase along with the exposure concentration. The mean index values of the gill histopathology ranged from 5.25-7.67 and classified as moderate to severe. Gills characteristics and T. granosa protective behaviour potentially limit Diuron accumulation in the soft tissue.

Association of Physicochemical Characteristics, Aggregate Indices, Major Ions, and Trace Elements in Developing Groundwater Quality Index (GWQI) in Agricultural Area.

The aim of this study was to propose a groundwater quality index (GWQI) that presents water quality data as a single number and represents the water quality level. The development of the GWQI in agricultural areas is vital as the groundwater considered as an alternative water source for domestic purposes. The insufficiency of the groundwater quality standard in Malaysia revealed the importance of the GWQI development in determining the quality of groundwater. Groundwater samples were collected from thirteen groundwater wells in the Northern Kuala Langat and the Southern Kuala Langat regions from February 2018 to January 2019. Thirty-four parameters that embodied physicochemical characteristics, aggregate indicator, major ions, and trace elements were considered in the development of the GWQI. Multivariate analysis has been used to finalize the important parameters by using principal component analysis (PCA). Notably, seven parameters-electrical conductivity, chemical oxygen demand (COD), magnesium, calcium, potassium, sodium, and chloride were chosen to evaluate the quality of groundwater. The GWQI was then verified by comparing the groundwater quality in Kota Bharu, Kelantan. A sensitivity analysis was performed on this index to verify its reliability. The sensitivity GWQI has been analyzed and showed high sensitivity to any changes of the pollutant parameters. The development of GWQI should be beneficial to the public, practitioners, and industries. From another angle, this index can help to detect any form of pollution which ultimately could be minimized by controlling the sources of pollutants.

Baseline distribution and sources of selected agricultural runoff in the bottom water of an active cockle farming area, Bagan Pasir, Perak, Malaysia.

This paper aims to study the spatial and temporal patterns of selected agricultural runoff, specifically in terms of glyphosate, nitrate, and ammonia in bottom water, as well as their possible sources, within an active cockle farming area in Bagan Pasir, Perak, Malaysia. Samples were taken along the cockle farming area from March to November 2019. Glyphosate was analyzed using HPLC with both extraction and derivatization methods using 9-fluorenyl-methyl chloroformate (FMOC-Cl), while nitrate and ammonia levels were determined using the standard Hach method. Generally, glyphosate, nitrate, and ammonia were present within the study site with the average concentration of 37.44 ± 12.27 µg/l, 1.65 ± 0.52 mg/l, and 0.37 ± 0.19 mg/l, respectively. The results suggest that glyphosate and nitrate might be derived from an inland source, while a uniform and low level of ammonia suggested might originate from lithogenic origins. Continuous monitoring remains encouraged.

Prospect of abandoned metal mining sites from a hydrogeochemical perspective.

Land exploitation for mining sector may leave a series of environmental impacts on our ecosystem if not appropriately managed. Therefore, the present study attempts to evaluate the various environmental aspects due to abandoned metal mining including former iron ore, bauxite, and tin mining lands in view of its hydrogeochemical behavior. Mine-impacted waters and sediments were ascertained from former mining ponds, mine tailings, and impacted streams for interpretation of aqueous and sediment geochemistry, major and trace elements, hydrochemical facies, chemical weathering rate and CO2 consumption, and water quality classification. Results indicated that the environmental impact of the long-abandoned iron ore mine was still evident with some high concentration of metals and acidic pH. Higher concentrations of Fe and Mn in water were noticeable in some areas while other trace elements (Pb, Zn, As, Cd, Cr, and Cu) were found below the recommended guideline values. Sediment quality reflected the trend of water quality variables mainly associated with metal(loid) elements, resulting in potential ecological risk, classified as having low to moderate risk. There were variations in terms of hydrochemical facies of the waters suggesting the influence of minerals in water. The chemical weathering rate suggests that contribution of carbonate mineral weathering was more important (up to 60%) than silicate weathering. The resulting CO2 consumption by mineral weathering was estimated to be in the range of 1.7-9.8 × 107 mol/year (former bauxite and tin mining areas can act as temporary sinks for CO2). Water quality classifications according to several chemical indices (Kelly's ratio, sodium absorption ratio, soluble sodium percentage, residual sodium carbonate, magnesium absorption ratio, and permeability index) were also discussed in regards to mine water reuse for irrigation purpose. The findings suggest that a holistic approach that integrates all important hydrogeochemical aspects is essential for a thorough evaluation of the implication of medium- to long-term mining exploitation on its surrounding ecosystems. This would be beneficial in light of restoration potential of degraded mining land so as for future mitigation strategies in the mining sector.

Impact of Diuron contamination on blood cockles (Tegillarca granosa Linnaeus, 1758).

Examination of the impact of Diuron contamination on blood cockles (Tegillarca granosa) was conducted by combining field screening at three sampling events and a toxicity test. Diuron was extracted using the liquid-liquid extraction (LLE) technique and analyzed using HPLC-UV. The median lethal concentration (LC50) of Diuron on T. granosa was tested under a 72-h exposure. Diuron in water samples ranged from not detected (ND) to 3910 ppb, which was the highest concentration detected in samples after the irrigation water was discharged from the paddy plantation. Diuron was not detected in sediment samples. Mortality of T. granosa ranged from 4.74 to 38.33% with the highest percentages recorded after the release of the irrigation water. The LC50 value of Diuron was 1.84 ppm. This study suggests that irrigation water from paddy plantation that drifts to coastal areas containing Diuron harms T. granosa at the study area.

Mineral carbonation of sedimentary mine waste for carbon sequestration and potential reutilization as cementitious material.

This study highlights the importance of mineralogical composition for potential carbon dioxide (CO2) capture and storage of mine waste materials. In particular, this study attempts to evaluate the role of mineral carbonation of sedimentary mine waste and their potential reutilization as supplementary cementitious material (SCM). Limestone and gold mine wastes were recovered from mine processing sites for their use as SCM in brick-making and for evaluation of potential carbon sequestration. Dominant minerals in the limestone mine waste were calcite and akermanite (calcium silicate) while the gold mine waste was dominated by illite (iron silicate) and chlorite-serpentine (magnesium silicate). Calcium oxide, CaO and silica, SiO2, were the highest composition in the limestone and gold mine waste, respectively, with maximum CO2 storage of between 7.17 and 61.37%. Greater potential for CO2 capture was observed for limestone mine waste as due to higher CaO content alongside magnesium oxide. Mineral carbonation of the limestone mine waste was accelerated at smaller particle size of < 38 µm and at pH 10 as reflected by the greater carbonation efficiency. Reutilization of limestone mine waste as SCM in brick-making exhibited greater compressive strength and lower water absorption compared to the bricks made of gold mine waste. The gold mine waste is characterized as having high pozzolanic behaviour, resulting in lower carbonation potential. Therefore, it has been noticeable that limestone mine waste is a suitable feedstock for mineral carbonation process and could be reutilized as supplementary cementitious material for cement-based product. This would be beneficial in light of environmental conservation of mine waste materials and in support of sustainable use of resources for engineering construction purposes.

Passive bioremediation technology incorporating lignocellulosic spent mushroom compost and limestone for metal- and sulfate-rich acid mine drainage.

Passive bioremediation of metal- and sulfate-containing acid mine drainage (AMD) has been investigated in a batch study. Multiple substrates were used in the AMD remediation using spent mushroom compost (SMC), limestone, activated sludge (AS), and woodchips (WC) under anoxic conditions suitable for bacterial sulfate reduction (BSR). Limestones used were of crushed limestone (CLS) and uncrushed limestone, provided at two different ratios in mixed substrates treatment and varied by the proportion of SMC and limestone. The SMC greatly assisted the removals of sulfate and metals and also acted as an essential carbon source for BSR. The mixed substrate composed of 40% CLS, 30% SMC, 20% AS, and 10% WC was found to be effective for metal removal. Mn, Cu, Pb, and Zn were greatly removed (89-100%) in the mixed substrates treatment, while Fe was only removed at 65%. Mn was found to be removed at a greatly higher rate than Fe, suggesting important Mn adsorption onto organic materials, that is, greater sorption affinity to the SMC. Complementary with multiple treatment media was the main mechanism assisting the AMD treatment through microbial metal reduction reactions.

The occurrence and potential ecological risk assessment of bauxite mine-impacted water and sediments in Kuantan, Pahang,Malaysia.

Recent bauxite mining activities in the vicinity of Kuantan, Pahang, have been associated with apparent environmental quality degradation and have raised environmental concerns among the public. This study was carried out to evaluate the overall ecological impacts on water and sediment quality from the bauxite mining activities. Water and sediment samples were collected at seven sampling locations within the bauxite mining areas between June and December 2015. The water samples were analyzed for water quality index (WQI) and distribution of major and trace element geochemistry. Sediment samples were evaluated based on geochemical indices, i.e., the enrichment factor (EF) and geoaccumulation index (I geo). Potential ecological risk index was estimated to assess the degree to which sediments of the mine-impacted areas have been contaminated with heavy metals. The results showed that WQIs of some locations were classified as slightly polluted and contained metal contents exceeding the recommended guideline values. The EFs indicated minimal to moderate enrichment of metals (Pb, Cu, Zn, Mn, As, Cd, Cr, Ni, Co, and Sr) in the sediments. I geo showed slightly to partially polluted sediments with respect to As at some locations. The potential ecological risk index (RI) showed that As posed the highest potential ecological risk with RI of 52.35-60.92 at two locations, while other locations indicated low risk. The findings from this study have demonstrated the impact of recent bauxite mining activities, which might be of importance to the local communities and relevant authorities to initiate immediate rehabilitation phase of the impacted area.

Greenhouse gas emissions during plantation stage of palm oil-based biofuel production addressing different land conversion scenarios in Malaysia.

The environmental impacts with regard to agro-based biofuel production have been associated with the impact of greenhouse gas (GHG) emissions. In this study, field GHG emissions during plantation stage of palm oil-based biofuel production associated with land use changes for oil palm plantation development have been evaluated. Three different sites of different land use changes prior to oil palm plantation were chosen; converted land-use (large and small-scales) and logged-over forest. Field sampling for determination of soil N-mineralisation and soil organic carbon (SOC) was undertaken at the sites according to the age of palm, i.e. <5 years (immature), 5-20 and >21 years (mature oil palms). The field data were incorporated into the estimation of nitrous oxide (N2O) and the resulting CO2-eq emissions as well as for estimation of carbon stock changes. Irrespective of the land conversion scenarios, the nitrous oxide emissions were found in the range of 6.47-7.78 kg N2O-N/ha resulting in 498-590 kg CO2-eq/ha. On the other hand, the conversion of tropical forest into oil palm plantation has resulted in relatively higher GHG emissions (i.e. four times higher and carbon stock reduction by >50%) compared to converted land use (converted rubber plantation) for oil palm development. The conversion from previously rubber plantation into oil palm plantation would increase the carbon savings (20% in increase) thus sustaining the environmental benefits from the palm oil-based biofuel production.

Potential ecological and human health risks of heavy metals in surface soils associated with iron ore mining in Pahang, Malaysia.

The composition of heavy metals (and metalloid) in surface soils of iron ore mine-impacted areas has been evaluated of their potential ecological and human health risks. The mining areas included seven selected locations in the vicinity of active and abandoned iron ore-mining sites in Pahang, Malaysia. Heavy metals such as Fe, Mn, Cu, Zn, Co, Pb, Cr, Ni, and Cd and metalloid As were present in the mining soils of the studied area, while Cu was found exceeding the soil guideline value at all sampling locations. However, the assessment of the potential ecological risk index (RI) indicated low ecological risk (RI between 44 and 128) with respect to Cd, Pb, Cu, As, Zn, Co, and Ni in the surface soils. Contributions of potential ecological risk [Formula: see text]by metal elements to the total potential ecological RI were evident for Cd, As, Pb, and Cu. Contribution of Cu appears to be consistently greater in the abandoned mining area compared to active iron ore-mining site. For non-carcinogenic risk, no significant potential health risk was found to both children and adults as the hazard indices (HIs) were all below than 1. The lifetime cancer risk (LCR) indicated that As has greater potential carcinogenic risk compared to other metals that may induce carcinogenic effects such as Pb, Cr, and Cd, while the LCR of As for children fell within tolerable range for regulatory purposes. Irrespective of carcinogenic or non-carcinogenic risk, greater potential health risk was found among children (by an order of magnitude higher for most metals) compared to adults. The hazard quotient (HQ) and cancer risk indicated that the pathways for the risk to occur were found to be in the order of ingestion > dermal > inhalation. Overall, findings showed that some metals and metalloid were still present at comparable concentrations even long after cessation of the iron ore-mining activities.